Bolt Tension Meter

 

Checkline Logo

The TI-MINIMAX Ultrasonic Bolt Tension Monitor, is a state of the art instrument designed to measure elongation produced by tightening a threaded fastener. The TI-MINIMAX can accurately measure the elongation of fasteners of virtually any material from 1/2 inch to 10 feet in length. The measurement is achieved by determining the change in the transit time of an ultrasonic shock wave along the length of the fastener as the fastener is tightened. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener.

 bolt tension monitor ti minimax

Features

  • The first cost effective ultrasonic solution available on the market.
  • Visually compare the unloaded to the loaded waveform.
  • Display Options - RF, Rectified, Large Digits with Limits Bar.
  • Effectively monitor your bolts during periodic shutdowns over the service life of the fastener.
  • Measurement quanities - Time (nanoseconds), Elongation, Load, Stress, and %Strain.
  • Display Resolution - 1/8" VGA 240 x 160 pixels.
  • Stores 8000 readings and waveforms in multiple groups.
  • Built-in Linear regression or vector for optimizing load measurements.
  • The Auto Set feature automatically optimizes detection and adjusts display.
  • Hi/Lo alarm tolerance limits work in conjunction with the data port and external pump shut-off device.
  • IP 65 Rated

 

Specifications

Measuring Range From 1" to 48" (25.4mm to 122cm) bolts
Time Nanoseconds
Elongation Change in length (inches/millimeters)
Load Force load applied (pounds kIP or kN Killonewtons)
Stress Force for unit area stress applied (pounds kPSI or megapascals MPa)
Strain % percentage strain applied (inches per inch or millimeters per millimeter)
Resolution +/- .00001 inches (0.0001 mm)
Velocity Range .0492 to .3936 in/ms
1250 to 9999 meters/sec
Calibration
Fixed, Single, and Two point zero calibration options.
Select bolt material types from a preset or custom list.
Units English & Metric / Fahrenheit & Centigrade
Measuring Modes Pulse-Echo (standard)
Pulse-Echo w/Gate (fine adjust)
Pulser Square wave pulser with adjustable pulse width (spike, thin, wide)
Receiver Manual or Auto Set gain control with 40dB range
Timing 10 bit 250 MHz digitizer
Display Modes A-Scan - Rectified +/- (half wave view), or RF (full waveform view)
Alarm Limits Set hi and lo tolerances with audible beeper, viewable scan bar, and visual LEDs
Data Logger (Internal) Total of 8,000 readings, multiple bolt groups. Stores both waveform views, nanoseconds, elongation, load, stress, and strain for each reading
Memory 16 megabit non-volatile ram
Transducer Single Element (1 to 10 MHz & 1/8" to 1" diameters)
Transducer Cable Lenght 10 foot (custom lengths available, inquire)
Temperature Probe for automatic temperature compensation
Setup Memory 64 custom user defined setups. Factory setups can also be edited by the user
Gate Gate used to fine adjust where the detection point occurs
Auto Set Locates the detection signal, optimizes the gain setting, and adjusts the overall display to show the waveform and detection point automatically
Field Calibration Vector & linear regression. Includes Factory calibration traceable to national standards
Power Three 1.5V alkaline or 1.2V NiCad AA cells.
Typically operates for 150 hours on alkaline and 100 hours on NiCad (charger not included.)
Dimensions Width (2.5in/63.5 mm)
Height (6.5 in/165 mm)
Depth (1.24 in/31.5 mm)
Weight 13.5 ounces (with batteries)
Operating Temperature 14 to 140F (-10C to 60C)

 

Complete Kit

The TI-MINIMAX is supplied as a kit including Gauge, 2 AA batteries, 4 oz. Bottle of Couplant, RS232 Transfer Cable, Lemo to DB9 M/F 10' Lemo to Microdot Transducer Cable, Windows Utility Software Carrying Case, Operation Manual.
Probes/Transducers and Calibration blocks are sold separately

pdficon largeBrochure