impact instruments 
 
 
 Tel : + 27 11 704 7001 / 5 / 8
 Email : This email address is being protected from spambots. You need JavaScript enabled to view it.

SF6 Portable and Fixed Leak Detectors

SF 6 GasCheck 6000 New

R 18 500.00 excluding VAT 

SF6 GasCheck 6000

 

Applications

• SF6 Switchgear

• Service & maintenance in SF6 switchgear production 

• Mobile leak detection on test equipment (pressure, mass flow)

The ideal low cost SF6 leak detector

The SF6 GasCheck 6000 leak detector is a great device for mobile SF6 leak detection. In practical use, it has a detection threshold of 1x10-6 mbar l/s, which makes it perfectly suitable for simple leak detection applications on SF6 switchgear.The easy to use, processor controlled instrument features both an audible alarm and an LED bar graph display, letting you know if a small, medium or big leak has been detected.The leak detector automatically compensates all ambient influences like temperature changes or movement of air in the room. Intelligent control sets up the instrument appropriately for the ambient situation.

The ‘Auto Shift’ function

The exclusive ‘Auto Shift’ function compensates for any SF6 concentration that may be present at the measuring site, e.g. caused by previously escaped leakage gas.SF6 GasCheck 6000 automatically detects the highest present gas concentrations, and selects the corresponding measuring range. It then uses the present gas concentration as its zero line, and begins to look for even higher gas concentrations, which by all means occur when a leak is approached. This will again be indicated audibly and visually. It is thus possible to determine leaks even in an already seriously contaminated area.

pdficon largeBrochure

The assessment of large leaks is often useful to get an idea of a component’s leak tightness, before much more sensitive instruments like SF6 LeakCheck P1:pmust be used.

 

Kit Includes :

1 x SF6 GasCheck 6000 leak detector 
1 x tranport case 
1 x sensor protective cap 
1 x water vapour filter 
1 x user manual (mulitlingual)

Gas Check G Sniffer G1 G2 G3

 

GasCheck G - Gas Leak Detector

Applications

Designed specifically for the detection of gas leaks, the GasCheck range of gas leak detectors respond rapidly to any gas, or gas mixture. The advanced micro-thermal conductivity sensor of the GasCheck G accurately detects the smallest of gasleaks down to cc/sec, mg/m³ or ppm levels.  The GasCheck IS gas leak detector is the only ATEX approved, Intrinsically Safe leak detector on the market. Its Intrinsic Safety proves an ideal tool for use in areas classified as zone zero flammable, and can safely detect flammable gases. GasCheck gas leak detectors are conveniently calibrated against helium and are particularly sensitive to ammonia, argon, butane, hydrogen, SF6 and refrigerants.

 SF 6 portable New

 

SF6 Gas Leak Detector Leak Check P1 : P 

Highly sensitive, detection guaranteed every time. 

SF6 LeakCheck P1:p is designed for the location, leak testing and measurement of SF6 leaks in high voltage electrical switchgear. The revolutionary SF6 leak detector rapidly detects leaks down to 1 x 10-8 ml/sec, with a response and clear down of less than 1 second. The instrument’s award winning Negative Ion Capture (NIC) technology with non-radioactive source eliminates problems of registration, storage and transportation.The LeakCheck P1:p  SF6 leak detector is unaffected by large leaks. The detector will continue to remain uncontaminated even after exposure to 100% SF6 gas.

Applications

High voltage switchgear leak testing

  • Switchgear commonly engages SF6 as a highly insulating medium to prevent sparking between high voltage components. Impact Instruments successfully detected SF6 leaks on 11 and 66 KV swithgear as well as ring main units which were leaking. SF6 is costly to replace, causes ozone depletion in the upper atmosphere, and its loss may result in catastrophic failure of equipment.

GIS Leaks

  • Gas insulated switchgear is filled with SF6, Impact Instruments performed many hugely succesful tests using the Leak Check P1 : P, at Eskom and municipal sites. The Leak Check P 1 : P was even found to be "too" sensitive at times. Detection of volatiles in industrial environments is an essential part of maintenance of health and safety of personnel, and can be carried out by continuous monitoring of personnel or at appropriate fixed loactions

pdficon largeBrochure

SF6 AreaCheck P2 – Fixed SF6 Leak Detection

 
  • Detect and alarm to leakage in indoor GIS (gas insulated switchgear) substations
  • Protect personnel, reduce emissions and wastage
Designed for fixed continuous SF6 area monitoring, the AreaCheck P2 with 12-point network controller rapidly detects low-level SF6 leaks.The fixed SF6 leak detector utilises relay output for immediate awareness of detected leaks, and presents no cross sensitivity with any other gas or moisture in the air. The AreaCheck P2 has no filter problems due to its minimum air intake (compared to pump operated SF6 AreaCheck P2systems). Instrument setup is carried out easily via a computer or network interface, allowing optimal protection from unauthorised access. The SF6 AreaCheck P2 has a built in low flow alarm and self-diagnostic testing. Serviceable components are comprised in the user exchangeable SmartSensor, with a lifetime of up to 12 months. Measuring stations are maintenance-free, ensuring instrument downtime is minimised. The SF6 leak detector can be effectively used as a stand-alone instrument or with the P2 network controller and up to eleven other SF6 AreaCheck P2s.GIS

pdficon largeBrochure