DSP Logger Expert
Advanced Six Channel, Vibration and Machine Health Analyser
Incorporating FFT, automatic bearing and lubrication state, balancing, phase analysis, data collection and machine current signature analyis into a powerful machine diagnostic tool.
Brochure
Choose from the following models :
3 Configurations to choose from :
1. DSP Logger Expert 150 – Machine Balancer
DSP Logger Expert hardware module with single and dual plane balancing firmware and standard DSP Machinery Control View Software.
Machine Balancing in 1 and 2 planes
- Single Plane Balancing
- Dual Plane Balancing
- No-Phase Balancing
- Dual Channel spectrum
- Calculations to add or subtract weight
- Final Correction Report
- Report Generator
2. DSP Logger Expert 200 – Data Collector
DSP Logger Expert hardware module with data collector firmware and full DSP Machinery Control Software (see in-depth software functions below)
Data Collector
- Multilocation polling
- Route-equipment-point-measurement
- Route visualization tools
- Route regeneration of unmeasured points
- Route history, including last 5 captures
- Mechanical status tools
- Equipment diagram
- Equipment pictures
- Automated function: quick or detailed
- Alarm system in spectrum or scalar
- Manual measurement status system
3. DSP Logger Expert 300 – Vibration Analyser, Measurer, Data Collector and Balancer (Can be upgraded to include Test I go later)
DSP Logger Expert Hardware Module with Data Collector Firmware, Vibration Measurer and Analyser Software, Machine Balancing Firmware, Phase Analyser Firmware and full DSP Machinery Control Software (see in-depth software functions below)
- Bearing Measurement
- Bearing Condition
- Lubrication
- Trending
- High Peaks
- Spike Energy®
- Amplitude by failure frequencies
- Spike Energy® State
- ISO 10816 Measurement
- ISO 10816 Status
- Balancing Status
- Alignment Status
- Looseness Status
- Trend
- Dual Channel
- Bearing Condition
- Mechanical, ISO Condition
- Dual channel recording Function
Vibration Analyzer
- Preconfigured Spectral Measurement
- Velocity
- Displacement
- Acceleration
- Envelope
- Configurable Spectrum Measurements
- With Accelerometers
- With proximiters
- With Velocimeters
- AC
- Triaxial Spectral Measurements
- Dual Channel Scalar Measurements
- Scalar Multivariable Measurement
- Tachometer RPM Measurement
- Mechanical Status Tools
- ISO 10816 Status
- Balancing Status
- Alignment Status
- Looseness Status
Phase Analyzer
- Relative Phase Measurement
- Absolute Phase Measurement
- Samples to measure and position sensors
- Polar Graph
- Phase Trend
- Dual Channel WaveForm
Machine Balancing in 1 and 2 planes
- Single Plane Balancing
- Dual Plane Balancing
- No-Phase Balancing
- Dual Channel spectrum
- Calculations to add or subtract weight
- Final Correction Report
- Report Generator
Optional :
DSP Logger Expert "Test I go
"
DSP Logger Expert Hardware Module, Test I go firmware and standard DSP Machinery Control View Software
The Motor Current Signature Analysis (MCSA) “Test I go” performs functions for predictive maintenance programs, it identifies possible power circuit problems that degrade motor health, examines overall motor power conditions, monitors the load and observes motor performance whilst estimating energy savings. It is programmed to supply information on :
- Three phase Voltage levels
- Voltage balance/unbalance
- Harmonic and total distortion
- Rotor cage condition
- Motor efficiency
- Effective service factor
- Over-current
- Power factor correction
- Torque
- Load
Brochure
DSP Logger Expert 300 – 4 Functions + Test I go (Full Version Kit)
DSP Logger Expert Hardware Module, Data Collector Firmware, Vibration Measurer and Analyser Software, Machine Balancing Firmware, Phase Analyser Firmware, Test I go Firmware, Test I Go hardware full DSP Machinery Control Software and DSP Machinery Control View Software for electrical reporting.